New ! Replacement Crane Tub Spout
After numerous requests and a lot of “imagineering”, we have finally come up with a solution for the folks with a broken Crane tub diverter spout. As you may know, Crane used an “oddball” sized thread on many of their spouts, making it impossible to replace the spout with a new one. Not anymore! 
 

Crane Tub Waste and Overflow Cover Plate
The 1 5/8” bolt hole spacing make this plate unique. Chrome over Zinc, just like the originals. Outside diameter is 3 1/4”, accepts the oddball “flip-arm” used by Crane from the 1950’s up to the 1970’s. Please note, you’ll have to save the old lever mechanism from the old plate. The shaft portion is not made anymore.
665-F11250 Overflow plate 45.00

Crane Trip lever for above Overflow Plate
If you destroy the old lever removing it from the old plate, here’s the replacement. Chrome over zinc, measures 1 3/4” long. Be sure to salvage the shaft this goes on, replacements do not exist.....
665-F11248 Trip Lever 15.00

NEW CRANE DRAIN
Hard-to-find drain will fit most Crane sinks that have the internal fork in the overflow chamber. Due to their unique drain lifting mechanism, the only thing that will fit Crane sinks is one specifically designed for a Crane fixture. This OEM replacement has been machined from an original for an exact fit. Fork not included. Includes 4" x 1 1/2" tail piece.
24-CD Polished Brass, complete drain 250.00 
      Polished Nickel, complete drain 295.00

24-CDS Polished Brass stopper only 89.00 
       Polished Nickel stopper only, 118.00

Crane drain washer only. Flat washer for underside of sink on Crane drains. Use plumber’s putty under top drain flange and this replacement washer on the underside to re-seal Crane drains to the sink basin.
62-OCDW Crane drain washer only for original Crane Drains
(does not fit new Crane drain)  6.95

Replacement Drain Forks for Crane: Crane made at least 20 different fork assemblies for different models of sinks. If you have a broken fork, send the assembly to us and we’ll try to match it up with one from our stock. Click here for information on sending us your drain fork. If your sink is missing the fork entirely, the odds of

Crane Drain Nut/Tailpiece Adapter
We got tired of finding nice Crane sinks missing the nut on the bottom of the sink so we decided to make them.  This is the nut that both retains the drain and also converts the drain to the fine 1 1/2” tailpiece thread. (our part # 81-371) We highly recommend using our tailpieces, either the 90-F25 below, or the 81-371. Supplied with washer, and comes in both polished nickel for exposed plumbing and raw brass for hidden applications. Note, nut is not compatible with the above 24-CD replacement Crane drain

86-630 Crane drain nut, raw brass, 90.00
       Crane Drain nut, Polished Nickel, 105.00
        

Reducing Tailpiece for Crane Bathroom Sinks
Crane used an oddball tailpiece on many of their wall-hung and pedestal sinks. It’s actually a reducing tailpiece, necking the 1 1/2’ fine thread outlet down to 1 1/4”. This part was commonly used from 1915 or so until the early 1970’s. It mates to the above 86-630 nut. Measures 7 3/4” long, 17 gauge.
Note; does not fit 4” center slantback or deckmount lavatory sinks.
90-F25 Crane tailpiece, Chrome, 35.00
      Crane Tailpiece, Polished nickel 45.00
      

Crane Close-Coupled Toilet Flapper
Hard to find these days, these flappers were found in many toilets Crane made in the ‘60’s and early ‘70’s. After Crane was bought out, production ceased and aftermarket suppliers started reproducing them. Over time, production slowed, and it became hard to find again. Distinguished by the method of mounting, they are once again available. Flapper is retained to the flush valve by the elongated hole in the end. Definitely not your “standard” flapper.
80-0108F Crane Flapper 7.95